KBC MOTORCYCLE HELMETS
GENERAL CARE & CLEANING
CARING FOR HELMETS CORRECTLY:
In order for your KBC
motorcycle helmets to provide the maximum
level of performance and service, proper care and attention
to it's condition and general upkeep is essential. Clean
the exterior and interior of your KBC motorcycle
helmets regularly. Use a soft cloth with mild
detergent, using only lukewarm water. Never use gasoline
(petrol), thinners, benzene or any other solvents or chemicals
because they can adversely effect the shock absorbing inner
liner and plastic components.
The comfort liner and cheek pads are fully removable, washable
and replacements are available through your KBC dealer.
Carefully hand wash and air dry the comfort liner and cheek
pads when required. When the comfort liner is damp or wet
due to perspiration or rain, always dry the KBC
motorcycle helmets and liner in the shade,
gentle air movement through the material will speed the
drying process.
KBC MOTORCYCLE HELMETS SHIELD CARE
SHIELD CARE:
IT IS ABSOLUTELY ESSENTIAL THAT THE KBC MOTORCYCLE SHIELD
IS KEPT IN OPTIMUM CONDITION AT ALL TIMES. DETERIORATION
THROUGH SCRATCHES AND ROAD DEBRIS SUCH AS INSECTS AND GENERAL
ROAD FILM CAN SERIOUSLY REDUCE CLEAR VISION AND INCREASE
TE RISK OF CAUSING AN ACCIDENT WITH THE POTENTIAL FOR SERIOUS
INJURY TO YOURSELF AND OTHER ROAD USERS.
In order to maintain the KBC motorcycle helmets
shield condition you should clean it regularly
at fuel stops and while out riding. Never attempt to clean
KBC motorcycle helmets shield while riding the motorcycle.
ALWAYS STOP FIRST.
Clean KBC motorcycle helmets shield
only with clean, lukewarm water and a mild detergent. Never
use solvents or chemicals. Only use approved cleaning products
designed for KBC motorcycle helmets shields. Always use
a very soft lint free cloth and rub gently. Never use a
dry cloth to clean KBC motorcycle helmets shield, only immediately
after cleaning should you gently buff dry KBC
motorcycle helmets shield.
MIRRORED SHIELDS: Due to the technology
used in manufacturing mirror or iridium coated KBC motorcycle
helmets shields, these KBC motorcycle helmets shields scratch
or damage more easily than clear KBC motorcycle helmets
shields. Therefore these KBC motorcycle helmets
shields must be cleaned with even greater care.
DARK TINTED, SMOKE, BLACK AND MIRRORED SHIELDS SHOULD NEVER
BE USED AT NIGHT OR IN INCLEMENT WEATHER WHERE VISIBILITY
IS POOR AS THESE ARE DESIGNED ONLY FOR VERY BRIGHT RIDING
CONDITIONS (CHECK THE LEGALITY OF THESE SHIELDS IN YOUR
STATE OR COUNTRY AS IN SOME COUNTRIES THESE ARE ILLEGAL)
SHIELD SYSTEM LUBRICATION:
When servicing KBC motorcycle helmets,
use a silicone or vaseline (petroleum jelly) in small quantities
to provide a small degree of lubrication to moving parts
DO NOT PUT IT ON THE SHIELD AS THIS CAN REDUCE CLEAR VISION.
SHIELD REMOVAL - VR2 , VR3, Force RR, Force S KBC
Motorcycle Helmets
All KBC motorcycle helmets utilize a very simple and effective
KBC motorcycle helmets shield removal mechanism system.
NO TOOLS ARE REQUIRED. KBC motorcycle helmets
shield can be removed and replaced very easily and quickly.
Follow the diagram shown here. First, open KBC motorcycle
helmets shield and locate the KBC motorcycle helmets shield
spring pin. Pull downward on this component to release the
mechanism. The KBC motorcycle helmets shield will 'pop off'
or release very gently. Repeat on other side for total removal.
To reattach the KBC motorcycle helmets shield, locate KBC
motorcycle helmets shields central circular
mechanism and push into central spring loaded fixing point
on KBC motorcycle helmets ratchet plate. Apply moderate
pressure to both sides using your hands to latch KBC
motorcycle helmets shield onto the guide pins.
Then gently close the KBC motorcycle helmets shield. Open
and close the KBC motorcycle helmets shield several times
to ensure KBC motorcycle helmets shield is fixed correctly,
before using KBC motorcycle helmets,
as incorrect fixing could cause KBC motorcycle helmets shield
to shear or fall off when riding and could cause an accident.
NOTE: Some KBC motorcycle helmets share
a common KBC motorcycle helmets shield system. Please ensure
any new KBC motorcycle helmets shield purchased is for the
your KBC motorcycle helmets's system.
Models: VR3 KBC motorcycle helmets , VR2 KBC motorcycle
helmets , Force RR KBC motorcycle helmets
, Force S share a KBC motorcycle helmets shield system.
Models: FFR KBC motorcycle helmets
and TK8 use a different system. AR1 (Racer-1) and TK77 also
use a different system
SHIELD SEALING:
KBC motorcycle helmets are designed to offer KBC motorcycle
helmets shield sealing effect to prevent rain and wind penetration.
To ensure this operates efficiently, make sure KBC
motorcycle helmets shield ratchet system is
correctly aligned. Over time the factory fitting may become
loose. Adjust and tighten ratchet screws or ask your KBC
dealer for technical assistance.
SHIELD REMOVAL - FFR KBC MOTORCYCLE HELMETS SHIELD
SYSTEM
All KBC motorcycle helmets utilize a very simple
and effective KBC motorcycle helmets shield removal mechanism
system. NO TOOLS ARE REQUIRED. KBC motorcycle helmets shield
can be removed and replaced very easily and quickly. Follow
the diagram shown here. First, open the KBC motorcycle helmets
shield and locate the KBC motorcycle helmets shield spring
pin. Pull downward on this component to release the mechanism.
KBC motorcycle helmets shield
will 'pop off' or release very gently. Repeat on other side
for total removal. To reattach the KBC motorcycle helmets
shield, locate the KBC motorcycle helmets shields central
circular mechanism and push into central spring loaded fixing
point on KBC motorcycle helmets ratchet plate. Apply moderate
pressure to both sides using your hands to latch KBC motorcycle
helmets shield onto the guide pins. Then gently close the
KBC motorcycle helmets shield. Open and close the KBC motorcycle
helmets shield several times to ensure KBC motorcycle
helmets shield is fixed correctly, before
using KBC motorcycle helmets, as incorrect fixing could
cause KBC motorcycle helmets shield to shear or fall off
when riding and could cause an accident.
NOTE: Some KBC motorcycle helmets share
a common KBC motorcycle helmets shield system. Please ensure
any new KBC motorcycle helmets shield purchased is for the
KBC motorcycle helmets's system.
Models: VR3, VR2, Force RR, Force S share a KBC
motorcycle helmets shield system. Models:
FFR and TK8 use a different system. AR1 (Racer-1) and TK77
also use a different system.
SHIELD SEALING:
KBC motorcycle helmets are designed to offer KBC motorcycle
helmets shield sealing effect to prevent rain and wind penetration.
To ensure this operates efficiently, make sure KBC
motorcycle helmets shield ratchet system is
correctly aligned. Over time the factory fitting may become
loose. Adjust and tighten ratchet screws or ask your KBC
dealer for technical assistance.
KBC MOTORCYCLE HELMETS REMOVABLE
COMFORT LINER
REMOVING THE COMFORT LINER
COMPONENTS:
Most KBC motorcycle helmets feature a removable and washable
interior lining and have the option for the addition of
different size cheek pads (see your local dealer)
To remove the comfort liner: Remove lower neck trim first,
cheek pads second and remaining inner lining last.
When replacing lining, fit parts in reverse order.
The comfort liner fits in two recessed areas in the upper
front and lower rear of KBC motorcycle helmets.
Gently pull on the upper left or right corner of the liner
and pull it out past the plastic retention piece. Repeat
this process on the lower rear section to completely free
the comfort liner. Reverse this procedure to reattach the
comfort liner.
HIDDEN INTERNAL DAMAGE
Although KBC motorcycle helmets
is solidly constructed, it should be handled with care and
should be replaced in the event of your either dropping
the KBC motorcycle helmets onto a hard surface or rough
handling. Such abuse may damage the painted surface finish
or decrease its ability to protect.
IMPACT: Do not wear KBC motorcycle
helmets after an impact for any reason, even
if there are no visible damage showing on the KBC motorcycle
helmets, damage may have been caused to the internal structures
of KBC motorcycle helmets and
it's ability to absorb further energy may have been compromised.
REPLACE IMMEDIATELY.
KBC MOTORCYCLE HELMETS CHIN STRAP SYSTEM
CHIN STRAP:
Tightly fasten the chin strap by passing the end of the
strap through the D rings as shown in figure (A), then pull
the strap comfortably tight for a secure and snug fit. After
securing the chin strap, lift up firmly on the rear of KBC
motorcycle helmets to try to roll the KBC motorcycle helmets
off your head in a forward direction. If KBC
motorcycle helmets fit correctly it should
should be impossible to remove KBC motorcycle helmets in
this way. NOTE: If KBC motorcycle helmets comes off your
head during this test, please consult with your KBC dealer
to find another model that this does not happen with.
To remove KBC motorcycle helmets,
pull the D Ring tab (usually red woven material) outward
to release the strap tension as shown in figure (B), then
unthread the chin strap. Pull the chin straps outward then
rotate your KBC motorcycle helmets forward
and lift it off.
MODIFICATION CAUTION: Do not make any modification
on the chin strap. Do not make any modification on the interior.
Do not cut or extract or modify any parts of the polystyrene,
as you could drastically reduce the impact absorption features
of KBC motorcycle helmets. Use
only KBC genuine parts when you replace any part of
KBC motorcycle helmets, please refer
to your local KBC dealer for information on parts and accessories
available.
KBC MOTORCYCLE HELMETS GENERAL USE
AND ADVICE
VENTS: KBC motorcycle helmets are equipped
with many different venting systems designed specifically
for each KBC motorcycle helmets. Prior to use, please familiarize
yourself with the workings and functions of KBC
motorcycle helmets so as to ensure correct
operation while riding. Always take extra care while adjusting
any vent during your motorcycle ride.
SHIELD OPERATION: KBC motorcycle helmets
come with a special large operating tab to the left hand
side of KBC motorcycle helmets
shield. This tab allows easy operation with a gloved hand,
always use this tab to operate KBC motorcycle helmets shield
opening function. This is the quickest and safest method
of operation. Do not open KBC motorcycle helmets
shield while riding at high speed as damage to the KBC motorcycle
helmets or an accident could occur.
LUBRICATION: From time to time, KBC recommends
that a small amount of lubricating gel such as petroleum
jelly, or high quality, silicone-based lubricating gel or
spray is applied to KBC motorcycle helmets
shield mechanism and any switch gear and vent mechanisms.
Be careful not to accidentally apply any chemical or material
to KBC motorcycle helmets shield or other component pieces.
HELMET CLOTH COVER: KBC motorcycle helmets
are supplied with a protective outer cloth cover. This is
for protection of the paint finish only while being stored
or carried in a supporting bag and should not be under any
circumstances be used to carry KBC motorcycle
helmets on it's own.
HELMET SHARING: During its usage KBC motorcycle
helmets interior will naturally contour to the shape of
the owners head, therefore it is not recommended that any
KBC motorcycle helmets be worn
by anyone else other than the owner.
NEVER WEAR ANY OTHER HEAD GARMENT OR DRESSING UNDERNEATH
KBC MOTORCYCLE HELMETS AS THIS CAN REDUCE THE EFFECTIVENESS
OF THE HELMET IN AN ACCIDENT.
|
